A copy Speedster 1957 5th gen is a fifth-revision replica of the Omega Speedmaster 1957 re-edition, the 38.6 mm broad arrow chronograph from Omega's vintage trilogy. "5th gen" is a factory version number, not an Omega term, and it means the case, dial, hands and movement were reworked four times before the watch in front of you. If you typed "speedster," you almost certainly mean Speedmaster.
Duplicate Speedster 1957 5th Gen: The Ultimate Guide
Treat the generation number as a starting point for comparison, not a promise of quality. Two sellers can both advertise "5th gen" and ship very different watches, because no single factory owns the label.
What Does 5th Gen Mean on a Speedmaster 1957 Replica?
Replica makers release revisions the way software companies release patches. An early attempt usually misses the case diameter or the sub-dial spacing, and each later generation fixes one cluster of complaints from buyers.
duplicate speedster 1957 5th gen
By the fifth revision, most sellers claim corrected sub-dial spacing, sharper bezel engraving and a better movement. Verify every claim against real photos and measured specs instead of trusting the version number.
Reference Specs a 1957 Speedmaster Copy Should Match
- Case diameter: about 38.6 mm, clearly smaller than the 42 mm Professional Moonwatch.
- Case thickness: roughly 13.5 mm with a domed crystal.
- Hands: broad arrow hour hand, baton minute hand, long thin chronograph seconds.
- Bezel: steel tachymeter insert with a base 1000 scale and the dot over 90 marking.
- Dial layout: three sub-dials at 3, 6 and 9, with no date window.
- Logo: applied metal Omega symbol plus printed Speedmaster text below the 12.
- Crystal: hesalite or acrylic dome, never flat sapphire.
Movement Options Inside a 5th Gen Copy Speedster 1957
Most copies run one of three movements: a Chinese ST19 chronograph, a modified Seagull column wheel, or a cloned Lemania-derived manual wind built to mimic the Omega 1861. The 1957 re-edition is hand wound and has no rotor, so a spinning weight or an automatic winding feel is an immediate red flag.
Ask for a timing video that shows the chronograph start, stop and reset. A healthy movement snaps back to 12 and the sub-dial hands align cleanly.
Dial and Bezel Details That Separate Good From Bad
Look at the tachymeter first. Cheap copies print the scale thick and flat, and the dot over 90 sits too high or too low. On a good copy the numerals are thin, spacing is even and the steel insert has a brushed, slightly reflective finish.
Then check the sub-dials. Printing should stay crisp under magnification, the rings should be recessed or flat depending on the version, and the hands should reach the correct chapter marks. Lume color should be an even cream or pale green, never blotchy.
QC Checklist Before You Accept a 1957 Speedmaster Replica
- Confirm case diameter and lug width with a caliper photo.
- Check dot over 90 placement and bezel engraving depth.
- Verify hand alignment at 12 with the chronograph reset.
- Look for gaps at the lugs and a crown that sits flush.
- Ask about water resistance claims and treat them as marketing.
- Confirm the strap or bracelet matches the reference you want.
Legal and Ownership Reality Check
A replica is not a Speedmaster, cannot be serviced by Omega, and holds no collector value. Selling one as genuine is trademark infringement and fraud in most countries, including the United States. Buy a copy as a wearable curiosity, not as an investment.
FAQ
Is the 5th gen the best copy Speedster 1957 available?
It is usually the most refined version at that price point, but newer revisions appear every year. Compare specific photos and specs rather than trusting the number alone.
How much should a 5th gen 1957 Speedmaster replica cost?
Expect a wide range, and remember that price does not prove quality. A higher price should buy a better movement, sharper case finishing and stronger QC photos before shipping.